Thursday, February 10, 2011

R1150GS Givi E189 Topcase Rack Install

This documents installing a Givi E189 Topcase Rack on a 2001 BMW R1150GS. The rack is for Givi Monokey cases only.

I purchased the rack on craigslist for $60 shipped. It was missing some of the mounting hardware, so I didn’t save much versus buying new.

The install is pretty easy. It took me about fifteen minutes.

These are the parts I received:

The rack:

Install Givi E189 Topcase Rack on R1150GS 

The adapter plate:

Install Givi E189 Topcase Rack on R1150GS

The hardware (some is missing):

Install Givi E189 Topcase Rack on R1150GS

After a trip to the store and $8 later, the adapter with all required mounting hardware:

Install Givi E189 Topcase Rack on R1150GS

Tools I used:

Install Givi E189 Topcase Rack on R1150GS

1) use the flat screwdriver to pry the plastic cover off the top of the plate

Install Givi E189 Topcase Rack on R1150GS Install Givi E189 Topcase Rack on R1150GS

2) use the 5mm hex wrench to remove the stock bolts one at a time. If you remove both, the fender will fall down onto the tire.

Install Givi E189 Topcase Rack on R1150GS

3) After removing one, put some blue loctite on the new screw. Add the metal adapter plate and the long M6x70 1.00 flat head hex screw (4mm hex wrench) on one side as shown here on the left.

Install Givi E189 Topcase Rack on R1150GS

My kit only came with one, so I found another M6x60 1.00 flat head at the store which worked fine. Here you can see all three compared. the M6x60, M6x70 (kit), and stock.

Install Givi E189 Topcase Rack on R1150GS

4) remove the other stock bolt (5mm hex wrench), and replace with the new one (PH3 screwdriver). I added blue loctite to both before tightening. The flat heads are required for the rack to sit flush on the adapter.

Install Givi E189 Topcase Rack on R1150GS

5) These are M6x35 hex head bolts and M6x35 flat heads with nylon nuts (10mm) I purchased from the store since the hardware was missing.

Install Givi E189 Topcase Rack on R1150GS

6) Using more loctite, the other two flat heads, nuts, and washers, bolt the rear of the adapter to the rear of the luggage rack. I used the 10mm wrench and PH3 screwdriver here.

Install Givi E189 Topcase Rack on R1150GS

7) Using the M6x35 10mm hex head bolts, I added the included round washers and square washers. These are used to hold the nylon rack to the metal adapter. The metal adapter is already threaded, so no nuts needed. I also used blue loctite here as well.

Install Givi E189 Topcase Rack on R1150GS 

The bolts before tightening:

Install Givi E189 Topcase Rack on R1150GS Install Givi E189 Topcase Rack on R1150GS

8) Push the plastic cover onto the toprack. Then, using the small precision Phillips screwdriver, I installed the four small screws to hold it in place. They are quite delicate, so be careful.

Install Givi E189 Topcase Rack on R1150GS Install Givi E189 Topcase Rack on R1150GS 

9) Givi E189 topcase rack installed

Install Givi E189 Topcase Rack on R1150GS

10) I popped the extra power adapter off, so my case would sit flush. The power adapter is used to add brake lights to the topcase. I will probably add them in the future for more visibility.

Install Givi E189 Topcase Rack on R1150GS Install Givi E189 Topcase Rack on R1150GS

11) I removed these two bolts (5mm hex wrench) on the front of the frame near the rider’s seat. They hold the front of the metal plate the topcase rack is bolted to. I removed them to add blue loctite and tightened them up. One was slightly loose, so I was glad I checked.

Install Givi E189 Topcase Rack on R1150GS

My Givi V46 installed on the rack:

Install Givi E189 Topcase Rack on R1150GS

Here you can see the gap to the pillion seat. Plenty of room to lean back or to add a backrest.

Install Givi E189 Topcase Rack on R1150GS Install Givi E189 Topcase Rack on R1150GS

After the installed, I had the two stock bolts and the cable for the power adapter left over. These will be saved for future use.

Install Givi E189 Topcase Rack on R1150GS

No comments:

Post a Comment